2009 Nissan Sentra - Exhaust System (Section EX) (10 pages)

Posted on 27 Mar, 2015 by TheNexxuvas
Model: 2009 Nissan Sentra
File size: 0.18 MB


Other 2009 Nissan Sentra Manuals:


Download manual 2009 Nissan Sentra

Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 7, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 7.

Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.

Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.

Improper maintenance, including incorrect removal and installation of the SRS can lead personal, injury caused by unintentional activation of the system, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect.

Battery, and wait at least 3 minutes before performing any service, precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob.

Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work, if DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock.

Steering wheel rotation will become impossible, if steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged, when the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting.

Perform a self-diagnosis check of all control units using CONSULT-III, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, loosening or tightening heated oxygen sensors, before installing a new oxygen sensor (Use.

Or equivalent meeting MIL specification MIL-A-907), check exhaust pipes, muffler and mounting improper attachment, if necessary, repair replace damaged parts, exhaust front tube (except California) 9.

Perform the procedure with the exhaust system fully cooled down because the system will be hot, just after the engine turned off, use genuine NISSAN exhaust system parts or equivalent, which are specially designed heat, remove exhaust system components using power tools.

Remove heated oxygen sensor using Tool needed, be careful not to damage heated oxygen sensor, installation is in the reverse order removal, always replace exhaust gaskets and seal bearings with new ones when installing.

Before installing a new heated oxygen sensor, clean and apply anti-seize lubricant to exhaust system threads using suitable tool, discard any heated oxygen sensor which has been dropped from a height of more than 0, in) onto a hard surface such as a concrete floor; install new one, resulting in MIL coming on.

Remove deposits from the sealing surface of each connection, temporarily tighten nuts on the exhaust manifold side and bolts on the vehicle side, for unusual interference, and then tighten them specified torque, when installing each mounting rubber, avoid twisting or unusual extension up/down right/left.

Exhaust Manifold Exhaust Front Tube, securely insert seal bearing (2) into exhaust manifold (1) side, be careful not to damage seal bearing surface when installing.

Use of Cookies    About    Contact us
All marks are the property of their respective holders