2012 Nissan Juke - Instrument Panel (Section IP) (25 pages)

Posted on 25 Mar, 2015 by Prevenge
Model: 2012 Nissan Juke
File size: 1.41 MB


Other 2012 Nissan Juke Manuals:


Download manual 2012 Nissan Juke

Manual Description
SQUEAK AND RATTLE TROUBLE DIAGNOSES 5, (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along.

With a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front, air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SRS AIR BAG” and SEAT BELT”.

Always observe the following items preventing accidental activation, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision that would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal.

Injury caused by unintentional activation of the system, never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with.

Ignition ON or engine running, never use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, disconnect battery negative terminal advance.

Disconnect air bag system line advance, never tamper with or force air bag lid open, as this may adversely affect air bag performance, be careful not to scratch pad other parts, when removing or disassembling any part, be careful not to damage or deform it.

When removing parts with a screwdriver or other tool, cover the tool surface with vinyl tape protect parts, keep removed parts protected with shop cloth, if an unreusable part is removed, replace it with new one, tighten bolts and nuts firmly specified torque.

After reassembly is complete, check that each part functions correctly, remove stains via following procedure, dip a soft cloth in warm water, and then squeeze it tightly, dissolve a synthetic detergent in warm water (density of 2 to 3%), dip the cloth, then wipe off stain with.

Wipe the area with soft dry cloth, never use any organic solvent, such thinner benzine, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removes clips, pawls metal clips.

SQUEAK AND RATTLE TROUBLE DIAGNOSES, interview the customer if possible, to determine the conditions that exist when the noise occurs, conditions that exist when noise occurs, all the facts and conditions that exist when the noise occurs (or does not occur).

If there is more than one noise in the vehicle, perform a diagnosis and repair the noise that customer IP, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so that the customer, service adviser, and technician use the same language when describing, squeak – (Like tennis shoes clean floor).

Squeak characteristics include the light contact / fast movement / brought on by road conditions / hard surL, faces = high-pitched noise / softer surfaces = low-pitched noises / edge surface = chirping, creak – (Like walking on an old wooden floor), creak characteristics include firm contact / slow movement/twisting with a rotational movement / pitch.

Dependent on materials / often brought by activity, rattle – (Like shaking baby rattle), rattle characteristics include fast repeated contact / vibration or similar movement / loose parts/missing clip, knock – (Like a knock door).

Knock characteristics include hollow sounds / sometimes repeating / often brought by driver action, tick – (Like clock second hand), tick characteristics include gentle contacting of light materials / loose components / can be caused by driver O.

Use of Cookies    About    Contact us
All marks are the property of their respective holders