Download manual 2013 Nissan ArmadaManual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 2, precaution Necessary for Steering Wheel Rotation After Battery Disconnect 2, sIDE CURTAIN AIR BAG MODULE 13, sIDE AIR BAG (SATELLITE) SENSOR 16.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front.
Air bag, depending on the severity of a collision and whether the front occupants belted unbelted, information necessary to service the system safely is included in the SR and SB section Service Manual, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.
Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery, and wait at least 3 minutes before performing any service, before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait least three, for approximately three minutes after the cables are removed, it is still possible for the air bag seat belt.
Diagnosis sensor unit must always be installed with their arrow marks ⇐” pointing towards front, the spiral cable must be aligned with the neutral position since its rotations are limited, wheel and column after removal steering gear, handle air bag module carefully.
Facing upward and seat mounted front side air bag module standing with the stud bolt side facing down, conduct self-diagnosis to check entire SRS for proper function after replacing any components, after air bag inflates, the instrument panel assembly should be replaced damaged, always replace instrument panel pad following front passenger air bag deployment.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect, this Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM), remove and install all control units after disconnecting both battery cables with the ignition knob, always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing work.
DTC is detected, perform trouble diagnosis according self-diagnostic results, for models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mechanism is adopted key cylinder, for this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock, steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow procedure below before, supply power using jumper cables battery discharged, when the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting, perform a self-diagnosis check of all control units using CONSULT.
Replace control unit and passenger front seat cushion an assembly, the actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, removing and installing air bag lock, air bag direct-connect harness connector is damaged, the spiral cable must be replaced.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables wait least, when servicing the SRS, do not work from directly in front air bag module, always place air bag module with pad side facing upward, do not allow oil, grease or water to come contact with.
Installation is in the reverse order removal, after the work is completed, perform self-diagnosis to check that no malfunction is detected, driver air bag module harness connector, disconnect the harness connector wiper washer.
Switch, then pinch the tabs at wiper and washer switch base, slide switch away from steering column remove, remove the screws, release the clip, remove spiral.