2014 Nissan Altima - Interior (Section INT) (35 pages)

Posted on 24 Mar, 2015 by Vergingondisgust
Model: 2014 Nissan Altima
File size: 1.28 MB


Other 2014 Nissan Altima Manuals:


Download manual 2014 Nissan Altima

Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, sQUEAK AND RATTLE TROUBLE DIAGNOSES 9, fRONT PILLAR FINISHER : Removal Installation21, fRONT KICKING PLATE : Removal Installation - Inner21.

FRONT KICKING PLATE : Removal Installation - Outer22, rEAR KICKING PLATE : Removal Installation - Inner22, rEAR KICKING PLATE : Removal Installation - Outer22, bODY SIDE WELT : Removal and Installation Front Body Side Welt23.

BODY SIDE WELT : Removal and Installation Rear Body Side Welt23, generic Squeak Rattle Troubleshooting 10, cENTER PILLAR LOWER FINISHER : Removal, cENTER PILLAR UPPER FINISHER : Removal.

REAR PILLAR FINISHER : Removal Installation25, dASH SIDE FINISHER : Removal Installation, tRUNK ROOM TRIM & TRUNK LID FINISHER 33, tRUNK LID FINISHER : Removal Installation 33.

TRUNK FLOOR CARPET : Removal Installation 33, tRUNK SIDE FINISHER : Removal Installation 34, tRUNK CARGO NET : Removal Installation 34, tRUNK REAR FINISHER : Removal Installation 35.

Precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT, the Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death.

The event of a collision which would result in air bag inflation, all maintenance must be performed by, improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS.

When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with, when using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least three minutes before performing any service, when removing or disassembling each component, be careful not to damage or deform it.

May be subject to interference, be sure to protect it with shop cloth, when removing (disengaging) components with a screwdriver or similar tool, be sure wrap component, with a shop cloth or vinyl tape protect it, protect the removed parts with a shop cloth and prevent them being dropped.

Replace a deformed damaged clip, be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly, follow the steps below clean components.

Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area, then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty, then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off.

- For genuine leather seats, use a genuine leather seat cleaner, the actual shapes of the tools may differ those illustrated here, replace any clips which are damaged during removal installation, sQUEAK AND RATTLE TROUBLE DIAGNOSES.

Interview the customer if possible, to determine the conditions that exist when the noise occurs, customer's comments; refer to INT-13, "Diagnostic Worksheet", conditions that exist when noise occurs, all the facts and conditions that exist when the noise occurs (or does not occur).

If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that customer INT, after identifying the type of noise, isolate the noise in terms of its characteristics, are provided so the customer, service adviser and technician are all speaking same language when.

Use of Cookies    About    Contact us
All marks are the property of their respective holders