2013 Nissan Altima - Defogger (Section DEF) (43 pages)

Posted on 24 Mar, 2015 by Italiancito
Model: 2013 Nissan Altima
File size: 1.24 MB


Other 2013 Nissan Altima Manuals:


Download manual 2013 Nissan Altima

Manual Description
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" 3, cOMMON ITEM : CONSULT Function (BCM COMMON ITEM) 8, rEAR DEFOGGER : CONSULT Function (BCM REAR DEFOGGER) 9, wITH MANUAL A/C : Component Function Check.

WITH MANUAL A/C : Diagnosis Procedure19, wITH AUTO A/C : Component Function Check22, wITH AUTO A/C : Diagnosis Procedure22, rEAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT 28.

DRIVER SIDE DOOR MIRROR DEFOGGER 30, pASSENGER SIDE DOOR MIRROR DEFOGGER 32, pASSENGER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE 39, mIRROR DEFOGGER DO NOT OPERATE 35.

OPERATE BUT BOTH OF DOOR MIRROR, oPERATE BUT REAR WINDOW DEFOGGER OPERATES 37, nOT LIGHT, BUT REAR WINDOW DEFOGGER OPERATES 40, precaution for Supplemental Restraint System (SRS) "AIR BAG" "SEAT BELT.

The Supplemental Restraint System such as AIR BAG” and SEAT BELT PRE-TENSIONER”, used along, with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger certain, to avoid rendering the SRS inoperative, which could increase the risk of personal injury death, the event of a collision which would result in air bag inflation, all maintenance must be performed by.

Improper maintenance, including incorrect removal and installation of the SRS, can lead personal, injury caused by unintentional activation of the system, pRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS, when working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near sensor(s) with.

When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect, battery and wait at least 3 minutes before performing any service, when removing or disassembling each component, be careful not to damage or deform it, may be subject to interference, be sure to protect it with shop cloth.

When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap component K, with a shop cloth or vinyl tape protect it, protect the removed parts with a shop cloth and prevent them being dropped, replace a deformed damaged clip.

Be sure to tighten bolts and nuts securely specified torque, after installation is complete, be sure to check that each part works properly, follow the steps below clean components, dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe dirty area.

Then rub with soft, dry cloth, dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) wipe dirty, then dip a cloth into fresh water, wring the water out of the cloth and wipe detergent off, - For genuine leather seats, use a genuine leather seat cleaner.

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here, bCM (view with combination meter re- 2, front air control (rear window defogger 5, rear window defogger ground connec- 8.

Tor (view with rear pillar finisher RH removed), door mirror LH (door mirror defogger) (if equipped) (RH similar), operates the rear window defogger and the door mirror defogger with control signal, displays the rear window defogger ON to the display when detecting the operation rear.

The rear window defogger switch turned ON, turns the indicator lamp ON when detecting the operation rear window defogger, heats the heating wire with the power supply from the rear window defogger relay prevent, the rear window fogging up.

Operates the rear window defogger with the operation of rear window defogger switch, performs the timer control rear window defogger, the door mirror fogging up.

Use of Cookies    About    Contact us
All marks are the property of their respective holders